English	Bulgarian	Contact Us:

Home Metal detectors: PI907, PI807-KIT, PI701-KIT. Characteristics Metal detector PI 907 Metal detector PI 807-KIT Do-it-yourself Metal detector PI 701-KIT Do-it-yourself Theory of impulse metal detectors Spy detector Antennas: Do-it-yourself Bee poison History	Metal detector PI 807-KIT Do-it-yourself Microprocessor impulse metal detector with excellent characteristics. Construction KIT. It characterizes with an excellent stability of work, great depth detections. It works in mode "all metals". The PI 807-KIT can be constructed and ready for use without the use of a soldering-iron or a screw-driver. Any knowledge on electronics is not necessary. Characteristics: Full control of the microprocessor on the device's work Two potentiometers for additional settings -- sound volume and sensitivity (depth) 54 programmable settings parameters. All manually chosen parameters are automatically saved by the microprocessor. When switched on again, the metal detector works with the previously saved parameters. The metal detector can work with the default parameters. It is not necessary to be changed. You can choose between two types of coils -- round 11 inches, square 40 inches. The chosen coil is automatically saved by the microprocessor. When switched on again, the metal detector uses the saved coil. Option to work with an internal speaker. Option to work with additional headphones. Works with 12 rechargeable batteries type AA; 1,2V; 2000mAh Technical parameters size -- 94mm x 115 mm and 48 mm x 115 mm power supply -- rechargeable battery 2000 mAh, 12V Tolerance for the power supply voltage 9,5 V to 17 V Wrong battery placement protection Minimum power required -- 260 mA Maximum power used - 650 mA Works for 5 to 7 hours with one set of rechargeable batteries, depending on the coil and mode. 2 changeable coils : large square coil - 40 inches ( 100 x 100 mm) ( 100x100 cm ) small round coil - 11 inches (275 mm) Display parameters - 54 parameters -settings and modes for adjustment Power of the speaker - 1W Power of the headphones - 150 mW Sound signal frequency - 500Hz indication - sound signal from a built-in speaker or headphones slots on the front panel for headphones, 3mm slots on the back panel strong metal slot for the coils slot for recharging the batteries Control buttons on the front panel: mode - choosing a coil and settings parameter select- setting a value for a parameter save - saving the chosen coil or the value of the parameter in the micro processor Potentiometers for settings on the front panel sound volume depth or sensitivity Consists of : main scheme plate 94mm x 115 mm control and indication scheme plate 48 mm x 115 mm connection cables two coils without bodies with a protected cabel connected with the metal detector and input for plugging the metal detector in. The coils are with a size of 26 cm round and 100x100 cm square 3 mm headphones input construction manual use instructions Constructing the PI 807-KIT : Installing the main scheme plate and the plate for indication and control in a specially chosen box Installing the inputs for the headphones and the coils in the box Installing the high-speaker in the box Installing a 26 cm coil in a body or wrapping it with a bandage tape, or coating it with epoxide resin Installing in a body of PVC pipes the square 100 cm x 100 cm coil or mounting it on the outer side of the PVC pipes Installing the rechargeable batteries in the box Switching the metal detector on: Connect the coil via the listed in the instruction conductor, to the matching input of the metal detector If you're not using a high-speaker , plug the headphones in the matching input Turn the sound volume resistor to max left Turn the depth resistor to max left Switch the power supply on Wait for approximately 15-30 seconds Turn the sound volume resistor to one quarter to the right Turn right smoothly the depth transistor, until you can permanently hear sound Turn back left until the sound is off The metal detector is ready for use Price: Metal detector PI 807-KIT Do-it-yourself: main scheme plate 94mm x 115 mm control and indication scheme plate 48 mm x 115 mm connection cables two coils without bodies with a protected cabel connected with the metal detector and input for plugging the metal detector in. The coils are with a size of 26 cm round and 100x100 cm square 3 mm headphones input construction manual use instructions Price: - 175 EUR +delivery Characteristics metal detectors:-PI907, PI 807, PI701 main scheme plate 94 mm x 115 mm control and indication scheme plate 48 mm x 115 mm connection cabels

Metal detector PI 807-KIT Do-it-yourself

Metal detector PI 701-KIT Do-it-yourself

Theory of impulse metal detectors

Spy detector

Antennas: Do-it-yourself

Bee poison

History

Metal detector PI 807-KIT Do-it-yourself

Microprocessor impulse metal detector with excellent characteristics. Construction KIT. It characterizes with an excellent stability of work, great depth detections. It works in mode "all metals". The PI 807-KIT can be constructed and ready for use without the use of a soldering-iron or a screw-driver. Any knowledge on electronics is not necessary.

Characteristics:

Full control of the microprocessor on the device's work
Two potentiometers for additional settings -- sound volume and sensitivity (depth)
54 programmable settings parameters. All manually chosen parameters are automatically saved by the microprocessor. When switched on again, the metal detector works with the previously saved parameters.
The metal detector can work with the default parameters. It is not necessary to be changed.
You can choose between two types of coils -- round 11 inches, square 40 inches. The chosen coil is automatically saved by the microprocessor. When switched on again, the metal detector uses the saved coil.
Option to work with an internal speaker.
Option to work with additional headphones.
Works with 12 rechargeable batteries type AA; 1,2V; 2000mAh

Technical parameters

size -- 94mm x 115 mm and 48 mm x 115 mm
power supply -- rechargeable battery 2000 mAh, 12V
Tolerance for the power supply voltage 9,5 V to 17 V
Wrong battery placement protection
Minimum power required -- 260 mA
Maximum power used - 650 mA
Works for 5 to 7 hours with one set of rechargeable batteries, depending on the coil and mode.
2 changeable coils :
- large square coil - 40 inches ( 100 x 100 mm)
  ( 100x100 cm )
- small round coil - 11 inches (275 mm)

Display parameters -
- 54 parameters -settings and modes for adjustment
Power of the speaker - 1W
Power of the headphones - 150 mW
Sound signal frequency - 500Hz
indication - sound signal from a built-in speaker or headphones
slots on the front panel
- for headphones, 3mm
slots on the back panel
- strong metal slot for the coils
- slot for recharging the batteries
Control buttons on the front panel:
- mode - choosing a coil and settings parameter
- select- setting a value for a parameter
- save - saving the chosen coil or the value of the parameter in the micro processor
Potentiometers for settings on the front panel
- sound volume
- depth or sensitivity

Consists of :

main scheme plate 94mm x 115 mm
control and indication scheme plate 48 mm x 115 mm
connection cables
two coils without bodies with a protected cabel connected with the metal detector and input for plugging the metal detector in. The coils are with a size of 26 cm round and 100x100 cm square
3 mm headphones input
construction manual
use instructions

Constructing the PI 807-KIT :

Installing the main scheme plate and the plate for indication and control in a specially chosen box
Installing the inputs for the headphones and the coils in the box
Installing the high-speaker in the box
Installing a 26 cm coil in a body or wrapping it with a bandage tape, or coating it with epoxide resin
Installing in a body of PVC pipes the square 100 cm x 100 cm coil or mounting it on the outer side of the PVC pipes
Installing the rechargeable batteries in the box

Switching the metal detector on:

Connect the coil via the listed in the instruction conductor, to the matching input of the metal detector
If you're not using a high-speaker , plug the headphones in the matching input
Turn the sound volume resistor to max left
Turn the depth resistor to max left
Switch the power supply on
Wait for approximately 15-30 seconds
Turn the sound volume resistor to one quarter to the right
Turn right smoothly the depth transistor, until you can permanently hear sound
Turn back left until the sound is off
The metal detector is ready for use

Price:

Metal detector PI 807-KIT Do-it-yourself:

main scheme plate 94mm x 115 mm
control and indication scheme plate 48 mm x 115 mm
connection cables
two coils without bodies with a protected cabel connected with the metal detector and input for plugging the metal detector in. The coils are with a size of 26 cm round and 100x100 cm square
3 mm headphones input
construction manual
use instructions

Price: - 175 EUR +delivery

Characteristics metal detectors:-PI907, PI 807, PI701

main scheme plate 94 mm x 115 mm

control and indication scheme plate 48 mm x 115 mm

connection cabels

Copyright 2003-2006	All materials here are copyright protected	e-mail:office@igkelectronics.com